







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Enterprise Homeowners Choose Therma-Tru Construction
We provide independent Therma-Tru door and entry system service in Enterprise: diagnosis, repair, slab and hardware replacement, and full entry installation, all built to Therma-Tru’s published fit and finish standards. What sets our Therma-Tru work apart is that we treat the slab, sill, sweep, hinge, and glass frame as separate components, so you’re paying to fix the part that actually failed instead of replacing a whole door that still has years left. We are an independent service provider. Enterprise Construction Co is not affiliated with, authorized by, sponsored by, or endorsed by Therma-Tru.
Homes across Enterprise put real stress on entry doors. The valley’s sustained 100°F+ summers and intense sun load a west-facing door face for hours every afternoon, and the dry air pulls moisture out of wood composite frames. Door failures here tend to be heat failures, dust failures, or UV finish failures, and each one points to a different repair. Call (844) 761-9449 to talk through what your door is doing. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Enterprise Construction Co for Your Therma-Tru Construction?

Our technicians have up to 10 years of experience, and that time gets spent on details most door calls skip. We know the Fiber-Classic and Smooth-Star fiberglass slabs, the Signet series, and the Benchmark and Tru-Defense entry systems at the component level: how the adjustable sill seats, how the sweep rides the threshold, how the hinge screws bite into the lock rail, and how the glass frame is retained. That familiarity is why we can tell you within a few minutes of looking whether your problem lives in the hardware or in the slab itself.
Warranty-safe service matters here. Spray foam in the wrong place, an aftermarket sweep that doesn’t match the threshold profile, or oversized screws driven into a stripped hinge hole can all create a condition a manufacturer will point to later. We re-shim and re-hang slabs rather than forcing them, we match sills, sweeps, hinges, and glass frames to the exact door series, and we use quality aftermarket weatherseal only where Therma-Tru no longer supplies the part. Every job ends with a written record of what we replaced, which is the document you want in hand if a warranty question ever comes up. The same standard applies when a job grows into a larger renovation: windows, entry glass, bathroom work, and small kitchen updates all run through one point of contact instead of a string of separate trades.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Therma-Tru Construction Problems We Fix in Enterprise
These are the failure patterns we see most often on Therma-Tru entries in Enterprise, and why they happen.
- Bowed or warped fiberglass slabs. A west-facing Fiber-Classic or Smooth-Star face takes direct afternoon sun with no shade or overhang. The fiberglass skin and its core expand and contract differently, and over enough summers the slab can bow at the center until the door no longer seals against the frame or the latch catches. It’s a heat-loading problem, not a frame problem, though the frame has to be checked before anyone decides that.
- Sill and bottom-sweep seal failure. The adjustable sill and door sweep are the parts that touch the outside world on every open and close. Fine Nevada dust and wind-driven grit grind at the sweep edge, and the adjustable sill loses its seat as the slab settles. Daylight and dust show up under the door first, then along the corners.
- Finish delamination and bubbling from UV and dry heat cycling. Factory finishes on fiberglass and oak-grain skins take repeated UV exposure plus the daily swing between a sun-hot face and a cool night. The finish can bubble, lift, or stain, especially on south- and west-facing doors. Once moisture gets behind a lifted edge, the problem accelerates.
- Hinge and lock-rail loosening. Thermal expansion and contraction work on the screws every day of the year. Screws loosen, then re-tighten into a hole that has grown slightly larger, and eventually the fiberglass skin cracks around the screw hole. A door that sags and drags at the bottom corner is often showing this before anything is visible.
- Failed glass frames and sidelite seals. Entry doors with glass, and the sidelites beside them, rely on the frame and its seal to keep wind and dust out. Monsoon-season gusts push hard against that seal, and a frame that has loosened over years of heat cycling can let grit and water past the gasket.
Therma-Tru Parts & Our Repair-vs-Replace Approach

We match Therma-Tru OEM sills, sweeps, hinges, and glass frames to the exact door series, and we use quality aftermarket weatherseal only where Therma-Tru no longer supplies the part. We don’t claim to stock genuine Therma-Tru parts or to be a Therma-Tru dealer. We identify what fits your door, source it, and install it correctly.
Our repair-vs-replace rule is simple. On a sound, plumb, square frame, repair is the honest first call: a bad sill or a worn sweep is a service item, and re-shimming and re-hanging a slab that’s only slightly off can add years. A slab that has bowed past the point where the latch will line up, a cracked fiberglass skin, or a failed glass frame usually means slab replacement instead, because forcing those back into alignment never holds. Because we are not factory-authorized, we have no reason to push a new door when a sill and sweep will do. Call (844) 761-9449 for a free estimate and we’ll tell you which side of that line your door is on.
Our Therma-Tru Service Process – Step by Step
- 1
Diagnosis. We check the frame for plumb and square before anything else, then inspect the slab, sill, sweep, hinges, lock rail, and glass frame separately. We note where daylight or dust is getting through and whether the slab is bowed at the center or simply out of adjustment.
- 2
Repair or install. For a sill or sweep, we match the part to the door series and seat it correctly against the threshold profile. For a slab, we re-shim and re-hang, or set a new slab where the old one is warped or cracked. For glass and sidelites, we replace the frame and reseal to spec.
- 3
Test. We cycle the door through a full open and close, check the latch and deadbolt alignment, confirm the sweep meets the threshold with no daylight showing, and test the seal against a hose spray at the corners and sill.
- 4
Warranty record. You get a written summary of what was replaced, which parts were used, and what we found on the frame. That record is what a warranty conversation should be built on.
See the difference
Before
After
Before
After
Before
AfterTherma-Tru Products We Service & Install in Enterprise
We service and install Therma-Tru fiberglass entry doors across the Fiber-Classic, Smooth-Star, and Signet lines, along with the Benchmark and Tru-Defense entry door systems, in both smooth and oak-grain skin finishes. That covers the slab, the adjustable sill and sweep, hinges, lock rails, glass frames, and sidelites. We handle repair work on an existing door and full entry replacement where the frame or slab is past saving. If your Therma-Tru door needs a glass panel or sidelite replaced, that work falls under our window and door scope, so one visit can cover the entry and any adjacent glass. Not sure which series you have? Send us a photo of the door edge and the threshold and we’ll tell you what we’re working with.
We Also Service These Brands
Therma-Tru is one piece of a much larger material toolkit. We also work with KraftMaid and Wellborn cabinetry, Cambria and Silestone countertops, and Kohler fixtures, and our seven service lines run from roofing and windows to kitchen, bath, additions, fencing, and driveways. For a homeowner in Enterprise planning several improvements at once, that means one contractor and one point of contact instead of a revolving door of specialists handing off to each other.
FAQs – Therma-Tru Construction Service in Enterprise

No. We are an independent service provider. Enterprise Construction Co is not affiliated with, authorized by, sponsored by, or endorsed by Therma-Tru, and we don’t claim factory training or certification. What we do claim is component-level familiarity with Therma-Tru doors and the process discipline to service them correctly.
Yes. We match Therma-Tru OEM sills, sweeps, hinges, and glass frames to the exact door series, and we use quality aftermarket weatherseal only where Therma-Tru no longer supplies the part. We do not claim to stock genuine Therma-Tru parts or to be a Therma-Tru dealer.
Most sill, sweep, and hardware repairs are done in a single visit, and a slab replacement or full entry install is typically a one-day job once the parts are on hand. Glass and sidelite replacement depends on the panel size and frame condition. Call (844) 761-9449 with photos and we can usually tell you what the job involves before we arrive. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
We cover fiberglass entry doors across the Fiber-Classic, Smooth-Star, and Signet lines, plus the Benchmark and Tru-Defense entry door systems, along with the sills, sweeps, hinges, lock rails, glass frames, and sidelites that go with them. Call (844) 761-9449 and we’ll confirm coverage for your specific door.
Not if the service is done correctly. Warranty problems usually come from wrong-profile sweeps, spray foam in the wrong place, or oversized screws in a stripped hinge hole. We re-shim and re-hang slabs rather than forcing them, match parts to the series, and give you a written record of what was replaced so any warranty conversation has documentation behind it.
These are typical estimated ranges for related work, and the written estimate sets the final price. Entry door glass and sidelite replacement runs $4500 – $15000 as part of our window replacement scope, a small or partial kitchen remodel runs $9000 – $20000, and a full bathroom remodel runs $9000 – $28000. Call (844) 761-9449 for an exact quote on your door. Estimates are free.
Book Your Therma-Tru Service in Enterprise, NV
Whether your Therma-Tru door needs a sill and sweep or a whole new entry, we’ll check the frame, tell you honestly which way the repair goes, and set the price in writing before work starts. Enterprise Construction Co handles the entry, the adjacent windows, and the interior work that follows under one project manager. Call (844) 761-9449. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Enterprise Construction Co.












