







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Enterprise Homeowners Choose Cover Construction
We provide independent Cover cabinet installation, refacing and service in Enterprise, working with Cover frameless boxes, shaker and slab door fronts, painted and thermofoil finishes and soft-close hardware every week. What sets our Cover work apart is that we treat the cabinet box as the foundation and the door face as the wear part, so we diagnose why a Cover kitchen is failing before quoting a fix. One contractor handles the cabinets, the quartz countertops, the backsplash and the island. We are not affiliated with, authorized by or endorsed by Cover; we’re an independent construction company that knows the product and answers only to you. Call (844) 761-9449. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Enterprise Construction Co for Your Cover Construction?

Our technicians have up to 10 years of experience with frameless cabinet systems, and that matters more than a logo on a van. Cover boxes are full-overlay frameless construction, which means the hinges mount directly to the cabinet side rather than to a face frame. When the side panel softens or the screw holes wallow out, a door goes crooked and no amount of adjusting the hinge will fix it. We know the difference between a hinge that needs a quarter turn and a box that needs a proper insert or a replacement panel.
We use quality parts that fit Cover equipment: OEM hinges, drawer slides and door fronts when they’re still available, and quality aftermarket hardware when the original line has been discontinued. We don’t claim to stock genuine Cover parts, and we’re not a Cover dealer. What we do is source hardware that matches the mounting pattern and load rating so your doors line up and stay lined up.
Warranty-safe service means we don’t do anything that gives a manufacturer a reason to walk away. We don’t drill new hinge cups into a finished door when an adjustment will do, we don’t shim a box that’s out of square, and we document what we found and what we changed. If the boxes are sound and only the faces are failing, we tell you that. If the boxes are swollen or delaminated, we tell you that too, even when it costs us the easier job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Cover Construction Problems We Fix in Enterprise
Cover cabinets in Enterprise fail in a handful of predictable ways. Here’s what we actually get called about, and why it happens.
- Thermofoil door faces peeling or bubbling along the edges. This shows up first near the range and the dishwasher, where heat and steam hit hardest. The vinyl face is bonded to a substrate, and repeated cycling between a hot cooking zone and cooled cabinet interior works the adhesive loose at the edge. Once the edge lifts, moisture gets behind it and the peel runs.
- Painted shaker doors cracking at the stile-and-rail joints, with chipping at the corners. Painted shaker fronts move with humidity, and a Las Vegas Valley kitchen swings from humid summer cooling to bone-dry winter air. The joints flex, the paint film cracks along the seam, and corners take the abuse from elbows and pot lids.
- Soft-close hinges and drawer slides losing their dampening. The soft-close mechanism relies on a small internal damper. Dust, cooking grease and thousands of cycles wear it out, and the door starts slamming or stops closing flush. It reads like a defect. It’s wear.
- Frameless box joints loosening, screws pulling out of particleboard. Full-overlay frameless boxes carry all the door load on the side panels. When particleboard takes on and releases moisture across seasons, the screw threads lose their grip and hinges begin to sag. Doors drift out of alignment even after adjustment.
- Doors that no longer close flush or sit square in the opening. This is usually the sum of the problems above: a sagging hinge on one side, a slightly warped face on the other, and a box that’s moved a fraction out of square. Chasing it with hinge adjustment alone rarely holds.
Cover Parts & Our Repair-vs-Replace Approach

A typical Cover kitchen call starts with thermofoil door faces peeling along the bottom edge near the dishwasher or range, plus doors that no longer close flush after a few dry seasons. The usual causes are heat and steam degrading the face material and softened particleboard letting hinge screws wallow out. A qualified local pro pulls the affected doors, tests the box for swelling and square, replaces or re-secures hardware with proper inserts, and either refaces with new Cover-compatible fronts or replaces the worst boxes before resetting the countertop and backsplash.
That’s the general shape of the work. The decision point is the box. If the sides are flat, dry and hold a screw, the cheapest correct fix is new door fronts and fresh hardware, and the kitchen looks new without touching the layout or the counters. If the particleboard is swollen, crumbling at the hinge line or visibly out of square, a cosmetic patch just buys a year. We’ll recommend refacing or replacement and explain the reasoning before you commit.
We source quality parts that fit Cover cabinetry. We don’t stock or order OEM or genuine Cover parts, and we’ll say so plainly. Call (844) 761-9449 to schedule a free estimate and we’ll tell you which side of that line your kitchen is on.
Typical Estimated Cover Project Costs in Enterprise
These are typical estimated ranges for Enterprise. The written estimate sets the final price.
| Project | Typical Estimated Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Backsplash Installation | $800 – $2,500 |
| Kitchen Island Installation | $3,000 – $10,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
| Kitchen Remodel | $14,000 – $45,000 |
Two things push a Cover job toward the top of those ranges in Enterprise: the number of boxes being replaced versus refaced, and whether the countertop has to come off. A refacing job with fresh hardware and a re-set counter sits near the low end. A full kitchen remodel that replaces boxes, adds an island and runs a new backsplash sits near the high end.
Our Cover Service Process – Step by Step
- 1
Diagnosis. We open every door and drawer that’s misbehaving, check the box sides for swelling and delamination at the hinge line, test the cabinet run for square, and look at where the finish is failing. Heat zones near the range and dishwasher get close attention because thermofoil peel starts there.
- 2
Repair or install. For a repair, we pull the affected doors, install proper inserts where screws have wallowed, replace worn hinges and slides, and rehang with the correct reveal. For a refacing or install, we set and shim boxes level and square, mount Cover-compatible fronts, and align every soft-close door and drawer to the same gap.
- 3
Test. Every door gets opened and released to check the soft-close dampening. Every drawer gets loaded and run full travel. We check that doors close flush against the box without rubbing, that gaps are even across the run, and that the countertop sits level over the new boxes.
- 4
Warranty conversation. One point of contact, one warranty conversation. We tell you what we replaced, what we adjusted, what we left alone, and what to watch for next. If a hinge or slide we installed fails, you call us, not a manufacturer’s phone tree.
See the difference
Before
After
Before
After
Before
AfterCover Products We Service & Install in Enterprise

We install and service the full range of Cover kitchen cabinetry work: frameless full-overlay cabinet boxes, shaker and slab door fronts, painted and thermofoil finish options, and soft-close drawer and door hardware. That covers new cabinet installation in a remodel or addition, refacing an existing Cover kitchen with new fronts, island cabinetry, and hardware replacement when dampers wear out.
Focused areas on this page include Cabinet Installation & Refacing, Quartz & Granite Countertops, and Full Kitchen Remodeling. Most Cover work in Enterprise runs through those three, since cabinets and counters usually move together once a box gets replaced. We don’t claim to stock Cover products or to carry their full catalog. We work with the product in your kitchen.
We Also Service These Brands
We’re multi-brand, not single-brand dependent. Alongside Cover, we work with KraftMaid and Wellborn cabinetry, Cambria and Silestone quartz surfaces, and Kohler fixtures and faucets, so a kitchen mixing brands isn’t a problem for us. If your Cover boxes stay and you want a Cambria top and Kohler hardware, that’s one conversation with one contractor.
FAQs – Cover Construction Service in Enterprise
No. We are an independent construction and remodeling company, not affiliated with, authorized by or endorsed by Cover. We work with Cover cabinetry every week and know how the door styles, box construction and finish options interact with real kitchen layouts in Enterprise, but we answer to you, not to a manufacturer. Call (844) 761-9449 for a free estimate.
Yes, refacing is often the right call when the boxes are sound. Peeling thermofoil is a face problem, not a box problem, and if the cabinet sides are flat, dry and hold a screw, new door fronts and fresh hardware bring the kitchen back without tearing out the layout. If the particleboard is swollen or delaminated at the hinge line, refacing is a patch and replacement is honest. We check the box before recommending either. Call (844) 761-9449 to get an exact quote; estimates are free.
Usually not. Soft-close slides rely on a small internal damper, and damper wear plus dust and cooking grease is the normal cause when drawers stop self-closing or doors start slamming. Extreme desert heat and dry air harden the mechanism faster than a mild climate would. Replacement slides restore the function, and we match the mounting pattern so the drawer box doesn’t need modifying. Call (844) 761-9449 to book a look.
Not strictly, but it looks better if you do. If your existing Cover door front is still available, matching keeps the run seamless. If the original line is discontinued, we can source a close profile and finish, or intentionally contrast the island so the difference reads as a design choice rather than a miss. We’ll show you both directions before you decide. Call (844) 761-9449 for a free estimate.
Yes, if the boxes are level, square and structurally sound. Quartz needs a flat, rigid base; a sagging or out-of-square cabinet run will telegraph into the slab and can crack it at a seam. We check level and square before templating, and if a box needs re-securing or replacing, we handle that first. New countertops over sound Cover boxes is a common Enterprise job. Call (844) 761-9449 to talk it through.
A refacing job typically runs a few days once fronts and hardware are on site, and a full cabinet replacement with new counters and backsplash runs longer, often a couple of weeks depending on how many boxes change and whether the counter has to come off for templating. Occupied homes need the sink and range usable most nights, so we sequence around that. Call (844) 761-9449 for a written timeline and a free estimate.
Typical estimated ranges in Enterprise run $4,000 – $13,000 for cabinet installation, $2,000 – $6,500 for countertops, $3,000 – $10,000 for an island, and $14,000 – $45,000 for a full kitchen remodel, with small kitchens at $9,000 – $20,000. The written estimate sets the final price. Call (844) 761-9449 for an exact quote; estimates are free.
Book Your Cover Service in Enterprise, NV
Whether the thermofoil is peeling near the range or you’re planning a full kitchen remodel with new Cover fronts and a Cambria top, we’ll give you a written, line-item estimate with the scope spelled out. One contractor, one point of contact, one warranty conversation. Call (844) 761-9449. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Enterprise Construction Co.












