







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Enterprise Homeowners Choose CGI Construction
We provide independent CGI cabinet service in Enterprise, Nevada, and what makes our CGI work different is depth: we know how these boxes, hinges, glides and finishes actually behave after years of desert heat and daily use, and we repair, install and reface them without any manufacturer authorization or affiliation. CGI is a cabinetry brand we work with, not a badge we rent. If you already own CGI cabinets or you’re planning a kitchen around them, we can tell you what will hold up in an Enterprise home and what won’t.
Enterprise is a different kind of market for cabinetry work than most of the valley. This is stucco-over-frame suburbia built fast through the 2000s and 2010s, now hitting its first real renovation cycle. That timing matters for CGI owners: cabinets installed during the original build are old enough for finishes to fail before the boxes do.
Call (844) 761-9449 and we’ll talk through your project. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Enterprise Construction Co for Your CGI Construction?

Our technicians have up to 10 years of experience with semi-custom cabinetry, and CGI’s box construction, hinge and drawer-glide hardware and finish quirks are familiar ground. We’ve installed and serviced it across the Las Vegas Valley since it became a go-to for semi-custom layouts. That means we can look at a peeling door face or a drawer that won’t close flush and tell you what’s actually happening underneath, not just what’s visible.
The parts side matters as much as the diagnosis. We fit CGI cabinets with hardware and finishes that work with the box: OEM hinges, glides and touch-up finishes when they’re available, and quality aftermarket soft-close hardware when OEM parts are discontinued. We don’t force a part that doesn’t fit and we don’t pretend a hardware swap solves a structural problem.
Warranty-safe work is the third piece. We install to the cabinet manufacturer’s spec, shim and secure boxes properly, and keep the installation details documented so questions about coverage have a clear answer. We are an independent CGI service provider, not a CGI dealer, and we don’t claim factory training or certification. The company is licensed and insured, and every job starts with a free written estimate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common CGI Construction Problems We Fix in Enterprise
Most CGI cabinet problems we see in Enterprise come down to three things: heat and steam, worn hardware, and boxes that were never shimmed right on a slab floor. Here’s what each looks like and why it happens.
- Peeling or bubbling thermofoil door faces. Thermofoil and laminate faces fail at their edges first, especially on doors and drawer fronts beside the dishwasher and under upper cabinets where under-cabinet heat collects. Years of steam and radiant heat loosen the adhesive bond at the edge, then the face lifts and curls. The door body underneath is usually fine, so this is often a door-replacement problem rather than a whole-kitchen problem.
- Soft-close hinges and drawer glides losing adjustment. Soft-close hardware takes a beating in daily use, and after years of opening and closing, hinges drift out of adjustment and glides stop catching fully. The visible symptom is a door that hangs slightly or a drawer that won’t close all the way. The underlying cause is worn hardware and, sometimes, screw plates that have cracked or stripped in the cabinet box.
- Chalking or worn finishes on high-touch fronts. Painted and stained finishes wear on the surfaces hands actually touch: door fronts, drawer faces, and the edges around pulls. In a low-humidity desert climate, finishes can also chalk on sun-facing runs, so a kitchen with a west-facing window wall tends to show wear earlier on that side.
- Boxes racking or separating at the joints. A cabinet box that was installed without proper shimming over an uneven slab can rack slightly out of square over time, and when it does, joints separate and doors stop aligning with the box. This one points to the installation as much as the cabinet. Racked boxes need to be re-shimmed and secured before any new hardware will hold a clean adjustment.
- Water damage at the base and under the sink. Slow leaks, dishwasher spills and sink-cabinet moisture damage the cabinet bottom and side panels before they show up anywhere visible. Swollen particleboard or soft wood at the base of a box is the one condition that pushes a repair toward replacement, because the box loses the structure hardware needs to grip.
If any of this sounds like your kitchen, a free estimate will tell you which category you’re in and what it takes to fix it.
CGI Parts & Our Repair-vs-Replace Approach

For CGI cabinets, we source OEM hinges, glides and touch-up finishes when they’re available, and match with quality aftermarket soft-close hardware when OEM is discontinued. We don’t stock or warehouse parts, so what a job needs is ordered to fit that job. That’s a cleaner approach than pulling whatever’s on a shelf and forcing it to work.
The decision we make with you comes down to the state of the boxes:
- Reface or replace hardware when the boxes are solid and the problem is the door faces, finish wear or worn hinges and glides.
- Repair when a single door, drawer front or section is damaged and the rest of the run is sound.
- Full replacement only when water damage or structural racking makes repair uneconomical, meaning the box can no longer hold hardware or sit square.
That order matters. A reface or hardware replacement usually solves a cosmetic and mechanical problem at a fraction of replacement, and replacing a kitchen that just needed new door faces is money you didn’t have to spend. We’ll give you a written line-item estimate and let you decide. Call (844) 761-9449 to schedule it – estimates are free.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We look at the cabinets as a system: box square and shimming, hinge and glide condition, finish wear pattern, and moisture at the base and under the sink. We tell you which failure modes are present and which aren’t.
- 2
Repair or install. For repairs, we replace the affected faces or hardware and re-shim and secure racked boxes so doors align and close cleanly. For installs, we set and level boxes on the slab, secure them to the wall, and install doors, drawers and hardware to the cabinet manufacturer’s spec.
- 3
Test and adjust. Every door and drawer gets opened and closed, soft-close action checked, and alignment adjusted before we call it done. Hardware that doesn’t hold gets corrected on the spot, not left for a callback.
- 4
Warranty walk-through. We document what was installed or replaced and how, hand over finish touch-up where it applies, and answer your coverage questions so nothing is a guess later. Workmanship is backed by our warranty.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Enterprise
We service and install the kinds of CGI cabinetry that show up in Enterprise kitchens and baths: Euro-style full-overlay cabinets with soft-close hinges, shaker and slab door styles in painted and thermofoil finishes, plywood-box base and wall cabinet lines, and semi-custom pantry and island configurations. That spans both a full kitchen install and the smaller jobs that come later, like adding an island or replacing a run of doors. Whether you’re adding square footage or updating a single room, the same diagnostic and installation standard applies. We don’t stock cabinets or claim a local showroom; we specify to your project and install to spec.
We Also Service These Brands
CGI is one name in a broader material toolkit. We also work with KraftMaid and Wellborn cabinetry, Cambria and Silestone countertops, and Kohler fixtures and plumbing hardware. That range means a kitchen project can be planned as one job across cabinetry, counters and fixtures instead of three separate contractor visits. If your plans involve more than CGI, we can carry the whole scope.
FAQs – CGI Construction Service in Enterprise

No. We are an independent CGI service provider, not a CGI dealer, and we are not authorized, certified or factory-trained by the manufacturer. We install, repair and service CGI cabinetry using our own experience with the product, which is a different relationship than a dealer’s. Call (844) 761-9449 with questions about your cabinets.
Often yes. Peeling thermofoil is usually a door-face problem and the box underneath is sound, so we can source a matching door or reface the affected run. Exact matches depend on the finish still being produced or a close match being available, and we’ll tell you honestly which it is before you commit. Call (844) 761-9449 for a free estimate on door replacement or refacing.
It’s a repair in most cases. Drawers that stop closing fully usually have worn or out-of-adjustment glides, sometimes with cracked screw plates in the box, and replacing the glides and repairing the mounting points restores normal action. Replacement only comes up when the box itself is damaged. Call (844) 761-9449 to have it looked at.
Yes, and shimming is the part that matters. Slab-on-grade floors across Enterprise’s two-story and single-story tract homes are rarely perfectly level, so base cabinets get shimmed and secured so the boxes sit square and level. Skip that step and the boxes rack, joints separate and doors stop aligning. That’s why we treat shimming as part of the install, not an afterthought.
In most cases, yes. If the perimeter boxes are solid, an island can be added as its own unit, with utilities planned for its location and the island sized to leave proper clearance for doors, drawers and walkways. We’ll confirm the perimeter can stay before quoting it. Call (844) 761-9449 to schedule a free estimate.
We install to the cabinet manufacturer’s spec, document the work, and walk you through what the manufacturer covers versus what our workmanship warranty covers, so the lines are clear from the start. We don’t speak for CGI and we don’t promise coverage on their behalf.
Typical estimated ranges in Enterprise, Nevada, run like this. The written estimate sets the final price for your job.
| Service | Typical Estimated Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Kitchen Island Installation | $3,000 – $10,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
Door and hardware repairs run less than a full install because the scope is smaller. Call (844) 761-9449 for an exact quote – estimates are free and we don’t charge for the visit.
Book Your CGI Service in Enterprise, NV
Whether your CGI cabinets need new door faces, fresh soft-close hardware, or a full install on a new build-out, we’ll give you a straight diagnosis and a written line-item estimate. One point of contact, licensed and insured, work backed by our warranty. Call (844) 761-9449. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Enterprise Construction Co.












